01331 door control module driver side j386 single wire operation. PASSAT B5 3B6 CONVENIENCE WIRING DIAGRAM

01336

01331 door control module driver side j386 single wire operation

I am assuming this may just be a reset with a plug in meter. Interesting development today - the driver side door and rear door would not lock and also the internal door lock button by the handbrake would not work. Make sure that new keys are always coded into free memory positions where there is a zero in Group 003, field 2. Sounds like you have no issues there. When I was researching the problem, a common fault appeared to be water damage to the comfort control module.

Next

How to Replace a Blend Door Actuator in Under 15 Minutes

01331 door control module driver side j386 single wire operation

I did this today and all is well!! Niiden hajoaminen ei välttämättä anna vikakoodia, mutta voi silti tehdä jos jotain hassua. Simple fix is to take the positive lead off your batter for about 30 mins or so and reconnect. I understand there is a sensor on the gear box for the reverse lights, etc. Step 1: Remove the Lower Dash Panel or Glove Box Using a small socket and ratchet remove the mounting bolts that hold the under dash plastic cover on the passenger side. I repaired mine got a second hand unit from ebay or breakers the only thing that you will need to do is to recode the door keys can by done with vagcom. For additional details, refer to our.

Next

01331

01331 door control module driver side j386 single wire operation

Tosin nyt tuli mieleen, että entä jos akku on kuitenkin tullut tiensä päähän. A small universal might be needed to help remove the screws in awkward places. And also the aircon which is usually very cold, suddenly stopped giving me cold air this one may be non-connected but it is unusual for it to go from very cold to no cold air at all. Sincer nu l-am mai intalnit pana acum. First of all I need a major service kit.

Next

Help solving a door locking problem

01331 door control module driver side j386 single wire operation

The blower is not working but there appears to be heat coming from the vents. It should be pretty easy to check the door looms as the failure point is between the door and car body. It is not about being scared , it is how much money and time you need to send and is it really worth it. Left it at that as it wasn't really causing too much bother. Varsinkin jos on virrat ollut silloin päällä. It would randomly cut out while driving with no reason as to why.

Next

ajuda erros vag

01331 door control module driver side j386 single wire operation

All windows work except Rear Right. I put some 1w Led bulbs in in place of 5 or 7w and they kept blowing fuses straight away, took them back to Halfrauds and replaced them with Osram or Philips and no further problems. The next day I took master control unit out of door disconnected all wires, cleaned pins etc, and put back together, also I took off positive and negative battery cables off battery, cleaned them , put them back on and tightened good, Well , I turned the key and everything worked,??? This actuator then moves temperature and air direction doors inside the heater plenum box which are designed to control mode settings such as temperature, floor, mid vent, defrost and fresh air or re-circulation modes. Siellä siis ainakin on jotain häikkää, mutta voiko se aiheuttaa myös tuon kaasuongelman? My issue started with a dead battery, so I don't know why this worked, but it did. Ainakin apukuskin puolen johtosarjassa ehkä muissakin on todennäköisesti johtoja poikki, koska keskuslukituskaan ei siinä toimi, mutta voiko se vaikuttaa tähän? Doesn't look like water has been gathering at any time recently. Here is my scan data, where could be the actual problem? There are no connectors, other than the ones inside the door card and at the rear door control module. I suggested to Andrew that we do another scan in a week or so to see what else has come up.

Next

01336

01331 door control module driver side j386 single wire operation

Got the car back in today and found all the same codes recorded in the convenience module, will be checking the loom for crumbled joints in the morning but thinking that I might have to order a new module. Good Luck and let us know how it is going. Does it look like one of the control modules is toast? I took the battery out but everything is bone dry. They didn't charge me and I asked for a list of the fault printout which they gave me. To test the blend door operation and too double check that you are changing the correct actuator motor turn the blower motor on and work the door in each way. So your wiring could be different. Be sure to check the wiring harness connector terminals they should match identically.

Next